 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| CMD6392 4-Channel BTL Driver for Players The CMD6392FP is a 4-channel BTL driver for CD player motors and actuators. It has an internal primary filter, and can be directly connected (without attached components) to the servo PWM output of all drivers other than the spindle driver. FApplications CD players, CD-ROM drives FFeatures 1) HSOP 28-pin package allows for miniaturization of applications. 2) PWM input is filtered by the internal primary filter, eliminating the need for attached resistors and capacitors, thereby helping reduce the number of components. Resistor and capacitor time constants can also be changed with attached components. 3) Internal thermal shutdown circuit. 4) Internal mute circuit. FAbsolute maximum ratings (Ta = 25_C) FRecommended operating conditions (Ta = 25_C) * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: server@ceramate.com.tw Tel:886-3-3214525 Http: www.ceramate.com.tw Page 1 of 8 Rev 1.2 Oct.24, 2002 Fax:886-3-3521052 CMD6392 4-Channel BTL Driver for Players FBlock diagram * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: server@ceramate.com.tw Tel:886-3-3214525 Http: www.ceramate.com.tw Page 2 of 8 Rev 1.2 Oct.24, 2002 Fax:886-3-3521052 CMD6392 4-Channel BTL Driver for Players FPin descriptions * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: server@ceramate.com.tw Tel:886-3-3214525 Http: www.ceramate.com.tw Page 3 of 8 Rev 1.2 Oct.24, 2002 Fax:886-3-3521052 CMD6392 4-Channel BTL Driver for Players FElectrical characteristics (unless otherwise noted, Ta = 25_C, VCC = 8V, f = 1kHz, RL = 8) -25 * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: server@ceramate.com.tw Tel:886-3-3214525 Http: www.ceramate.com.tw Page 4 of 8 Rev 1.2 Oct.24, 2002 Fax:886-3-3521052 CMD6392 4-Channel BTL Driver for Players FInput / output circuits FCircuit operation (1) Fig. 3 shows the inputs from the digital servo IC for CH1-CH3 drivers (all drivers except the spindle). SW1 is on when the forward input signal (HIGH level, over 2.4V) is present. SW2 is on when the reverse input signal is present (Fig. 2) The constan current (I1)at this time enters the RC and generates an integral waveform based on the duty of the input waveform. The BTL is output from BUF1 and BUF2 (Fig. 4). To maintain the HIGH level with forward (or reverse) input, the DC voltage generated at point A is : I1 R 2.5V (reverse : *2.5V) This is the voltage generated relative VREF. The setting is such that a voltage differential of 5V is generated between output pins. The time constant is : R C = 2.4sec * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: server@ceramate.com.tw Tel:886-3-3214525 Http: www.ceramate.com.tw Page 5 of 8 Rev 1.2 Oct.24, 2002 Fax:886-3-3521052 CMD6392 4-Channel BTL Driver for Players This can be increased by inserting a capacitor between point A (pins 3, 11 and 18) and VREF. The constant current (Iconst) given in the electrical characteristics refers to I1 and I2 in Fig. 2. FOperation notes (1) The CMD6392FP has an internal thermal shutdown circuit. Output current is muted when the chip temperature exceeds 180_C (typically). (2) The output current can also be muted by lowering the mute pin (pin 15) voltage below 0.5V. (3) All four driver output channels are muted during thermal shutdown, muting and a drop in bias pin voltage. No other components are muted. (2) CH4 driver (spindle driver) Pins 23 and 25 are shorted inside the IC. Bias amplitudes are the primary type of inputs assumed. The level shift circuit converts the pre-stage amplifier output (centered on the bias level and impressed on pins 23 and 25) to positive and negative amplitudes centered on VREF. The level shift circuit's output is BTL-output from the buffer amplifier. Because of the high input impedance, the IC is designed to accommodate a filter comprising attached resistors and capacitors. (Example) For secondary filters * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: server@ceramate.com.tw Tel:886-3-3214525 Http: www.ceramate.com.tw Page 6 of 8 Rev 1.2 Oct.24, 2002 Fax:886-3-3521052 CMD6392 4-Channel BTL Driver for Players FElectrical characteristics curves * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: server@ceramate.com.tw Tel:886-3-3214525 Http: www.ceramate.com.tw Page 7 of 8 Rev 1.2 Oct.24, 2002 Fax:886-3-3521052 CMD6392 4-Channel BTL Driver for Players FExternal dimensions (Units: mm) HSOP-28 * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: server@ceramate.com.tw Tel:886-3-3214525 Http: www.ceramate.com.tw Page 8 of 8 Rev 1.2 Oct.24, 2002 Fax:886-3-3521052 |
Price & Availability of CMD6392
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |